e-paper-display/bcm2835-1.71/e-Paper/RaspberryPi_JetsonNano/c/readme_EN.txt

86 lines
4.1 KiB
Plaintext
Raw Blame History

This file contains invisible Unicode characters

This file contains invisible Unicode characters that are indistinguishable to humans but may be processed differently by a computer. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/*****************************************************************************
* | File : Readme_CN.txt
* | Author : Waveshare team
* | Function : Help with use
* | Info :
*----------------
* | This version: V1.3
* | Date : 2022-10-13
* | Info : Here is an English version of the documentation for your quick use.
******************************************************************************/
This file is to help you use this routine.
Since our ink screens are getting more and more, it is not convenient for our maintenance, so all the ink screen programs are made into one project.
A brief description of the use of this project is here:
1. Basic information:
This routine has been verified using the e-paper Driver HAT module.
You can view the corresponding test routines in the \lib\Examples\
of the project.
2. Pin connection:
Pin connection You can view it in DEV_Config.h in the \lib\Config\ directory, and repeat it here:
EPD => Jetson Nano/RPI(BCM)
VCC -> 3.3
GND -> GND
DIN -> 10(SPI0_MOSI)
CLK -> 11(SPI0_SCK)
CS -> 8(SPI0_CS0)
DC -> 25
RST -> 17
BUSY -> 24
3. Basic use:
Since this project is a comprehensive project, you may need to read the following for use:
You can see many test functions and macro definition Settings in main.c.
Specifying the macro definition for the EPD at compile time can directly compile the corresponding test program.
Please pay attention to which type of ink screen you buy. For detailed correspondence, see our Wiki and list.txt file.
Example 1:
     If you buy 3.7inch e-paper (V1) then you should add EPD=epd3in7 at compile time
sudo make clean
sudo make EPD=epd3in7
Example 2:
If you buy a 2.9-inch e-paper (B) (V1), you should add EPD=epd2IN9bc at compile time since the 2.9-inch type B and Type C are common driver code
sudo make clean
sudo make EPD=epd2in9bc
Example 3:
If you buy a 7.5-inch e-paper (V2), you should add EPD=epd7in5V2 at compile time
sudo make clean
sudo make EPD=epd7in5V2
An executable file is then generated: epd
Run: sudo ./epd
If you modify the program, you need to run: make clear, and then make again.
4. Directory structure (selection):
If you use our products frequently, we will be very familiar with our program directory structure. We have a copy of the specific function.
The API manual for the function, you can download it on our WIKI or request it as an after-sales customer service. Here is a brief introduction:
Config\: This directory is a hardware interface layer file. You can see many definitions in DEV_Config.c(.h), including:
type of data;
GPIO;
Read and write GPIO;
Delay: Note: This delay function does not use an oscilloscope to measure specific values.
Module Init and exit processing:
void DEV_Module_Init(void);
void DEV_Module_Exit(void);
Note: 1. Here is the processing of some GPIOs before and after using the ink screen.
2. For the PCB with Rev2.1, the entire module will enter low power consumption after DEV_Module_Exit(). After testing, the power consumption is basically 0;
\lib\GUI\: This directory is some basic image processing functions, in GUI_Paint.c(.h):
Common image processing: creating graphics, flipping graphics, mirroring graphics, setting pixels, clearing screens, etc.
Common drawing processing: drawing points, lines, boxes, circles, Chinese characters, English characters, numbers, etc.;
Common time display: Provide a common display time function;
Commonly used display pictures: provide a function to display bitmaps;
\lib\Fonts\: for some commonly used fonts:
Ascii:
Font8: 5*8
Font12: 7*12
Font16: 11*16
Font20: 14*20
Font24: 17*24
Chinese:
font12CN: 16*21
font24CN: 32*41
\lib\E-paper\: This screen is the ink screen driver function;
Examples\: This is the test program for the ink screen. You can see the specific usage method in it.